search

Kepco KLR Series Developers Guide Manual de usuario Pagina 128

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 128
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 127
B-26 KLR-DEV 060713
-123,”Exponent too large” Command Error bit 5 Exponent E+3 or greater is invalid.
-141,”Invalid character data” Command Error bit 5 For example OUTP OFD or OUTP STOP instead of OUTP OFF.
-150,”String data error”
Command Error bit 5
Invalid characters were detected in numeric entry.For example E.1
instead of E+1 or 4d3 instead of 4.3.
-203,”Command protected” Execution Error bit 4 Password must be CENabled.
-207,”Location is empty” Execution Error bit 4 Recalled location has no data stored.
-211,”Trigger Ignored” Execution Error bit 4 Trigger ignored because output is off.
-213,”INIT ignored”
Execution Error bit 4
Request for measurement ignored because another measurement
already in progress.
-221,”Settings conflict”
Execution Error bit 4
E.g. , Invalid password from syst:pass:cen command. or Calibration
state not enabled but CALibrate command received.
-222,“Current, Voltage or Data out of
range”
Execution Error bit 4
Value (current or voltage) exceeds power supply rating or (data)
exceeds acceptable command parameters.
-223,”Data format error” Execution Error bit 4 Multiple decimal points, Multiple exponents, etc.
-224,“Illegal parameter value” Execution Error bit 4 For example, OUTP 2 instead of OUTP 1.
-226,“Lists not same length”
Execution Error bit 4
During a LIST command, number of DWEL list entries was not equal
to 1 and did not match number of LIST:VOLT or LIST:CURR entries.
-280,“Program Error“ Execution Error bit 4 LIST execution error, e.g., program already running.
-301,”Value bigger than limit” Device Error bit 3 E.g., requesting a voltage or current that exceeds the limit.
-302, “Mode changed to Voltage”
-302, “Mode changed to Current”
Device Error bit 3 Power supply operating in current mode changed to voltage mode.
Power supply operating in voltage mode changed to current mode.
-303, “Output Lead Fault” Device Error bit 3 Excessive voltage drop detected between power and sense lead.
-304, “Current Protection Fault” Device Error bit 3 Current exceeded programmed protection value.
-305, “Voltage Protection Fault” Device Error bit 3 Voltage exceeded programmed protection value.
-306, “Over Temperature Shutdown” Device Error bit 3 Internal temperature exceeded thermal protection limit.
-307, “Power Loss Fault” Device Error bit 3 Source power loss occurred.
-308, “Fan Fault” Device Error bit 3 Fan fault detected.
-310,”System Failure” Device Error bit 3 Program checksum incorrect.
-311,”Memory Error” Device Error bit 3 E.g., power-up NV RAM error, or CALibrate:STORe error.
-313,”Calibration Memory Lost” Device Error bit 3 No valid calibration found.
-314,”Save/recall memory error” Device Error bit 3 Using cell other than 1 - 40 for SAV and RCL.
-315,”Configuration Memory Error” Device Error bit 3 Configuration Memory Error.
-330,”Self Test Failed” Device Error bit 3 Self test failed.
-340,”Calibration Failure” Device Error bit 3 Unable to perform auto calibration.
-341,”Non Volatile Mem. CRC error”
Device Error bit 3
Power supply constants may be corrupted; recalibration may be nec-
essary.
-350,”Queue Overflow”
Device Error bit 3
More than 15 errors are in queue. Error queue was full, error events
have been lost.
-410,”Query interrupted”
Query Error bit 2
New command sent before data from previous query read. Previous
query data lost.
-430,”Query Deadlocked” Query Error bit 2 Over 255 characters received in single input string.
TABLE B-5. ERROR MESSAGES (CONTINUED)
ERROR MESSAGE
ESR ERROR BIT SET
(SEE PAR. A.5)
EXPLANATION
Vista de pagina 127
1 2 ... 123 124 125 126 127 128

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Proveedores De Energía Kepco KLR Series Developers Guide
Proveedores De Energía Kepco KLR Series User Manual Manual de usuario   (92 paginas)
Proveedores De Energía Kepco MAT 1/3 Rack Manual de usuario   (51 paginas)
Proveedores De Energía Kepco MAT Full Rack MAT 6V, 15V, 25V AND 36V MODELS Manual de usuario   (46 paginas)
Proveedores De Energía Kepco MBT Series Manual de usuario   (152 paginas)
Proveedores De Energía Kepco MST Series Manual de usuario   (44 paginas)
Proveedores De Energía Kepco MST 488 Programmer Manual de usuario   (68 paginas)
Proveedores De Energía Kepco RAX 50W Manual de usuario   (4 paginas)
Proveedores De Energía Kepco RAX 100W Manual de usuario   (4 paginas)
Proveedores De Energía Kepco RAX 175W Manual de usuario   (4 paginas)
Proveedores De Energía Kepco RAX 300W Manual de usuario   (4 paginas)
Proveedores De Energía Kepco RA 19-4B Manual de usuario   (36 paginas)
Proveedores De Energía Kepco RA 19-3B Manual de usuario   (42 paginas)
Proveedores De Energía Kepco RA 19-7B Operator Manual Manual de usuario   (40 paginas)
Proveedores De Energía Kepco RA 46 Manual de usuario   (2 paginas)
Proveedores De Energía Kepco RA 19-4C Operator Manual Manual de usuario   (56 paginas)
Proveedores De Energía Kepco RA 55 Manual de usuario   (14 paginas)
Proveedores De Energía Kepco RA 58 Manual de usuario   (2 paginas)
Proveedores De Energía Kepco RA 59 Manual de usuario   (18 paginas)
Proveedores De Energía Kepco RA 60 Rev 1, 2, 3 Manual de usuario   (24 paginas)
Proveedores De Energía Kepco RCW 750W Series Manual de usuario   (20 paginas)
  • Tl-audio Solar Infra Systems Mcdonalds RS Components Magnat Audio
  • Bifinett Microondas Seiko No Aluratek Antenas de la red Blue Rhino Calentadores espaciales AirLink Tarjetas de red
  • Samsung ML-2010 Maytag MSC21C6MDM Fly DS185 Sony CFD-370 LG F4J8FH2W
  • Samsung RF23HCEDBSR/AA Manual Sebo Airbelt K3 Manual de usuario Argox AS-8020CL Manual de usuario LG 23EA53VB-W Manual de usuario Uniden UM-525 Manual de usuario